Have you ever considered if the jets in your swimming pool could produce bubbles or if the water could undergo a sudden decrease in level?
The fact that undetected air has sneaked into your pool lines and now causes the pool system to not work properly is manifested by these signs.
Air filtering problems can also cause the devices to fail, unwanted sounds to be produced, and even the equipment to be in danger in case of the repair's delay.
Accordingly, what is the method to get rid of this irritating problem?
Here, we will explore the most scientifically proven methods to drive away air from your pool lines, ensuring your swimming pool has good shape and is ready for a good swim every time.
9 Interesting Processes To Remove Air from Pool Lines
Air removal from your pool lines is vital not only for the finer functioning of your pool but also for the durability of your equipment.
Trapped air is a reason for raising issues, pool system inefficiencies, and even some harmful consequences.
Let's check out these nine easy steps to bring air out of your pool lines so that you can swim in joy.
1. Check and Adjust Water Levels
To be sure, the pool water level is at least halfway up the skimmer opening. If the swimming pool is too light, the skimmer can get filled with air.
Water should be added to the pool to ensure that it is at the proper level.
2. Inspect and Tighten Fittings
Take a careful look at all the visible pipes and fittings for any signs of a leak, like water drips or wet spots.
Use a wrench to tighten the pipe that may be loose; however, be careful not to overtighten, as this may cause damage.
3. Examine O-Rings and Gaskets
Look at the condition of the O-rings and gaskets on the pump lid, filter, and other devices.
If they are already worn out or damaged, replace them to make a proper seal on the surface.
4. Prime The Pump
Priming the pump enables the elimination of trapped air.
This is how you do it:
Start by switching off the pump.
Start with the removal of the pump lid, and then use a garden hose to fill the pump housing with water.
Put the lid back on and tighten it.
Then, switch on the pump again and check if it is still able to suck water without interruptions. In such a case, the procedure can be repeated if necessary.
5. Bleed The Air From The Filter
The majority of pool filters come with an air relief valve that helps release trapped air.
To use it:
Find the spot where the pump is running and where the air relief valve is located on top of the filter.
Slowly open up the valve. If you listen closely, you might even catch a faint hiss indicating that air is being let out.
As soon as the water shoots out, close the valve tightly.
6. Backwash The Filter
An unclean pool filter can block the flow of clean water, and consequently, air gets stuck.
Backwashing the filter can help:
First thing, turn off the pump.
Change the filter valve to the "Backwash" setting.
Re-start the pump and allow it to run for a clear sight in the sight glass. The usual time frame is 2–3 minutes.
Next, turn off the pump and go back to the filter position by turning the valve.
The last step is to turn the pump on again.
7. Check The Skimmer and Pump Strainer Baskets
Confirm that the skimmer and the pump strainer are clean and that they do not have any debris on their surfaces.
When blockages occur, the flow of water is reduced and air is introduced to the system.
8. Inspect And Adjust Valves
The valves of a pool should be checked to confirm that they are properly positioned.
The adjusting of the valves can be a means of enhancing the water flow and, therefore, eliminating air pockets.
9. Monitor The System
Once you have done these steps, you need to monitor the pool system for a few days to be sure there are no issues coming again.
Look for any new leaks or strange sounds that could possibly mean air still enters the lines.
Do you want to always have your pool in good condition and stay away from trouble related to the air? We are here for you!
To ensure that your system is maintained correctly and there is no air in your pool!
Identifying The Cause Of Air in Pool Lines
It is necessary to determine how the air is entering the pool lines before you can remove them.
Some of the common causes include:
Low Water Levels: Pumping the air into the water can cause skimmers to draw in air from below the water level.
Leaky Fittings or Pipes: Fractures, loose fittings, or old pipes will let air flow into the lines.
Faulty Seals: Damaged O-rings or gaskets on pool equipment can be a source of air leaks.
Improper Valve Positions: Wrongly placed valves can be a way for air to leak into the system.
Tips For Preventing Air in Pool Lines
Regular Maintenance: Thoroughly checking and caring for your pool equipment can stop air from getting into the lines.
Maintain Proper Water Levels: Check and keep the water level in your swimming pool properly.
Replace worn parts. Promptly: Worn or damaged parts should be replaced as soon as possible to avoid air leaks.
Proper Valve Positioning: Confirm that all valves are in the correct position and are working properly.
Conclusion
Air in your inground pool lines can become an ordinary but manageable problem if you have the right approach.
By following these in-depth directions, you can successfully eject the air from your pool lines, so your system runs smoothly without making noise.
Conducting preventive maintenance as well as acting promptly when necessary can be of great help in solving such issues in the future.
Our company specializes in fibreglass and gunite pool building. We are dedicated to making sure that you have a perfect pool environment every day.
If you are looking for a swimming pool professional or have any queries concerning the swimming pool system, do not hesitate to reach out to us.
Prevent technical difficulties and enjoy a smooth and hassle-free swimming experience!
Comments